The Opti-Mix® static mixing nozzle is specifically designed for crack injection epoxies and ensures thorough mixing of epoxy components:

• For use with both low viscosity and gel viscosity ETI formulations.
• Flow regulators ensure that resin and hardener fl ow at equal rates and prevent mixed epoxy from fl owing back out of the nozzle into the cartridge. This ensures thorough mixing and prevents mixed product from curing in the neck of the cartridge, causing blockage. Testing shows that mixing with the Opti-Mix® nozzle is 4 times more consistent than a standard spiral mixing nozzle.
• For use with pneumatic, battery and manual dispensing tools.
• Half the length of standard spiral mixing nozzles, allowing easy access in cramped conditions and reducing waste.
• Barbed end allows easy attachment to the E-Z-Click™ injection fitting.
• When dispensing low viscosity material, using a standard spiral mixing nozzle and a manual dispensing tool, resin and hardener surge unevenly through the nozzle without being thoroughly combined. The result is poorly mixed epoxy that will not fully cure and will not effectively repair the crack. The Opti-Mix® nozzle corrects this problem utilizing unique mixing elements and a fl ow regulator that allows the use of a manual tool with low viscosity epoxy.

GALLERY: roll over images below to see larger image

Opti-Mix® Mixing Nozzle

E-Z-Click™ Ports and Injection Fitting

The E-Z-Click injection system is comprised of a specially designed fitting and ports that take the mess out of your repair project while allowing you to work faster. The E-Z-Click injection fitting installs onto the end of the Opti-Mix® mixing nozzle and clicks onto the E-Z-Click™ ports during injection.

• Positive connection eliminates messy leakage, minimizing waste and clean-up.
• No drilling of ports: E-Z-Click ports perform while pasted to the surface of the concrete. No drilling required for most applications.
• Disconnect the fitting and the epoxy stops flowing, no leaky mess.
• After injecting, pull the head of the E-Z-Click port out to close it and prevent leakage.
• One person can work faster without having to hold the tube on the port.

GALLERY: roll over images below to see larger image

E-Z-Click™ Injection Fitting

EIP-EZA Flush Mount Port
(EIP-EZ similar in appearance)

EIPX-EZ
Corner Mount/
Drilled-In Port

ETR Epoxy Paste-Over

Ideal for pasting over the surface of cracks and attaching ports for pressure injection. The non-sag paste consistency enables paste-up on horizontal, vertical and overhead applications. Fast cure time means shorter time between paste-over and injection. Packaged as a kit in separate 8 oz. canisters which are mixed manually to yield 16 ounces of epoxy. Also ideal for small concrete repair application: spall repair and misc. patching. Each kit contains enough material to cover approximately 8 lineal feet of cracks.

• Material Safety Data Sheet: ETR16 (PDF)
• Material Safety Data Sheet: ETR16 en Español (PDF)

CIP Paste-Over

CIP is a fast-curing, two-part epoxy paste over material. It is used to seal cracks and to secure injection ports over concrete prior to epoxy or urethane foam injection repair. CIP sets up hard and can either be left on the concrete or ground or chiseled off at the completion of a crack injection job.

• Material Safety Data Sheet: CIP (PDF)
• Material Safety Data Sheet: CIP en Español (PDF)

CIP-F Paste-Over

CIP-F is a flexible, peelable and fast-curing polyurea paste-over material. It is used to temporarily seal cracks and to secure injection ports over concrete prior to epoxy or urethane foam injection repair. CIP-F can be peeled off at the completion of a crack injection job by pulling on starter tabs placed under the lead edge surface at the time of application or by prying under the paste-over.

• Material Safety Data Sheet: CIP-F (PDF)
• Material Safety Data Sheet: CIP-F en Español (PDF)

Crack Injection Paste-Over in Cartridge Delivery System

ETR16

CIP

CIP-F

Cure Schedule - ETR and CIP

Cure Schedule - CIP-F