ETI Injection Epoxies are specially designed formulations for the injection of cracks in concrete. ETI epoxies are two-component, 1:1 ratio, 100% epoxy solids formulations. They are available in 22 ounce side-by-side cartridges and are dispensed through a static mixing nozzle using a manual, battery or pneumatic dispensing tool. ETI is available in two viscosities: ETI-LV (low viscosity) and ETI-GV (gel viscosity) to handle a wide range of crack widths. Properly installed, they provide a repair that is both waterproof and high strength (structural).
GALLERY: roll over images below to see larger image
ETI-LV
ETI-GV
Caution - The ETI-LV must be used with the Opti-Mix nozzle (EMN022) for proper mixing. ETI-GV may also be used with the EMN22 mixing nozzle for gravity feed applications in large cracks.
FEATURES
- Chemically bonds with the concrete to provide a structural repair (meets the requirements of ASTM C-881 as a structural repair epoxy).
- Seals the crack from moisture, protecting rebar in the concrete from corrosion and flooring from moisture damage.
- Both viscosities formulated for maximum penetration under pressure.
- Side-by-side cartridge dispensing provides reliable mixing and ratio control when used with the New Simpson Strong-Tie® Opti-Mix™ static mixing nozzle.
- Eliminates the need for expensive bulk dispensing equipment. Either formulation can be dispensed using a manual or pneumatic dispensing tool (ETI-LV requires the use of the Opti-Mix nozzle, model EMNO22, which is included with the cartridge).
- Black and white components allow easier verification of mixing than systems utilizing same color components. The mixed epoxy is gray for a better color match with the concrete for exposed conditions.
- Suitable for pressure injection or gravity-feed applications.
- Non-shrink material resistant to oils, salts and mild chemicals.
ETI-LV Low Viscosity Injection Epoxy
- Low viscosity epoxy (1790 cps) for repair of fine to medium width cracks 1/64" - 1/4" in width.
- Low surface tension allows the material to effectively penetrate narrow cracks.
- Suitable for structural repairs.
ETI-GV Gel Viscosity Injection Epoxy
- Gel viscosity epoxy for repair of medium cracks 3/32 " - 1/4" in width.
- Decreases in viscosity under pressure for increased flowability.
- Suitable for structural repairs.
CODE REPORTS
APPLICATION
Epoxy-Tie injection epoxies are suitable for repairing non-moving cracks in concrete walls, floors, slabs, columns and beams. They can be used to inject cracks in damp or wet conditions with excellent results. Apply to concrete 40° F or above. For best results, warm material to 60° F or above prior to application.
INSTALLATION
LINKS:
- Limited Warranty Information
- Documents:
- Anchor Catalog Section (PDF)
- Product Submittal (PDF)
- Material Safety Data Sheet: ETI-LV (PDF)
- Material Safety Data Sheet: ETI-LV en Español (PDF)
- Material Safety Data Sheet: ETI-GV (PDF)
- Material Safety Data Sheet: ETI-GV en Español (PDF)
- Material Safety Data Sheet: ETR (PDF)
- Material Safety Data Sheet: ETR en Español (PDF)
ACCESSORIES / RELATED PRODUCTS
- Dispensing Tools
- Opti-Mix™ static mixing nozzle
- E-Z-Click Injection Ports & Fittings
- Paste Over Epoxy
SHELF LIFE
2 years in unopened cartridge.
TECHNICAL SPECIFICATIONS:
- ETI-LV: Meets the requirements of ASTM C-881 Type I, II, IV and V, Grade 1, Classes B & C. Approved under NSF/ANSI Standard 61.
- ETI-GV: Meets the requirements of ASTM C-881 Type I, II, IV and V, Grade 3, Classes B & C.
STORAGE CONDITIONS
For best results, store between 45°-90° F.
COLOR
Resin- white; Hardener- black. When properly mixed the adhesive will be a uniform gray color.
CLEAN UP
Removal of Cured Adhesive: Chip or grind off surface. Uncured Adhesive: Wipe up with cotton cloths. If desired, scrub area with abrasive, waterbased cleaner and flush with water. If approved, solvents such as ketones (MEK, acetone, etc.), lacquer thinner, or adhesive remover can be used. DO NOT USE SOLVENTS TO CLEAN ADHESIVE FROM SKIN. Take appropriate precautions when handling flammable solvents. Solvents may damage surface to which they are applied.
CHEMICAL RESISTANCE
Very good to excellent against distilled water, inorganic acids and alkalis. Fair to good against organic acids and alkalis, and many organic solvents. Poor against ketones.
| PROPERTY | TEST METHOD | ETI-LV RESULTS | ETI-GV RESULTS |
| Viscosity (75° F) | ASTM D 2393 | 1,790 cps | Non-Sag Gel |
| Bond Strength (moist cure) | ASTM C 882 | 2,500 psi (2 days) 2,530 psi (14 days) |
1,109 psi (2 days) 3,994 psi (14 days) |
| Tensile Strength | ASTM D 638 | 7,470 psi (7 days) | * |
| Tensile Elongation at Break | ASTM D 638 | 9.4% | * |
| Compressive Yield Strength | ASTM D 695 | 12,480 psi (7 days) | 11,564 psi (7 days) |
| Compressive Modulus | ASTM D 695 | 342,000 psi | 403,200 psi |
| Deflection Temperature | ASTM D 648 | 130° F | 131° F |
| Water Absorption (24 hours) | ASTM D 570 | 0.76% | 0.58% |
| Linear Coefficient of Shrinkage | ASTM D 2566 | 0.004 | 0.000 |
| Gel Time (60 gram mass) | ASTM C 881 | 120 min. | 135 min. |
| Initial Cure (72° F) | * | 24 hours | 24 hours |
ETI Cartridge System
- Bulk containers also available, contact Simpson Strong-Tie for details.
- Use only appropriate Simpson Strong-Tie® mixing nozzle in accordance with Simpson Strong-Tie instructions. Modification or improper use of mixing nozzle may impair epoxy performance.
