.300" Headed Fasteners with .157" Shank Diameter
PDPA Drive Pins - For Structural Steel and Extra Hard Concrete
- For up to 1/2" thick A36 and A572 Grade 50 structural steel (red strip load recommended)
- 157 diameter for greater compressive strength
- Manufactured with tight tolerances for superior performance
PDPA
.300" Headed Fasteners with .145" Shank Diameter
*Up to 2 1/2 ", ** Up to 1 1/2"
PDP
.300" Headed Fasteners with .177" Shank Diameter
*Up to 2 1/2 ", ** Up to 1 1/2"
PDPH
.300" Headed Fasteners with .145" Shank Diameter - Mechanically Galvanized
Mechanical Galvanizing meets ASTM B695, Class 65, Type 1.
*Up to 2 1/2 ", **Up to 1 1/2 "
PDPMG
.300" Headed Fasteners with .177" Shank Diameter - Mechanically Galvanized
Mechanical Galvanizing meets ASTM B695, Class 65, Type 1.
*Up to 2 1/2 ", **Up to 1 1/2 "
PDPHMG
316 Stainless Steel .300" Headed Fasteners with .145" Shank Diameter
*Up to 2 1/2 ", ** Up to 1 1/2"
PDPSS
.300" Headed Fasteners with .145" Shank Diameter
and 3/4" Metal Washers
*Up to 2"
PDPW
.300" Headed Fasteners with .145" Shank Diameter
and 1" Metal Washers
*Up to 2"
PDPWL
.300" Headed Fasteners with .145" Shank Diameter and 1" Metal Washers - Mechanically Galvanized with Protective Sleeve
- Provides added corrosion protection in preservative-treated lumber. See corrosion information.
- Plastic sleeve protects and preserves coating during installation; washer will not scrape off coating.
- Plastic sleeve prevents washer slipping during installation.
Mechanical Galvanizing meets ASTM B695, Class 65, Type 1.
*PDWLS has a square washer.
PDPWLMG (patent pending)
.300" Headed Fasteners with 1" Metal Washers
with .177" Shank Diameter
*Up to 2 "
PDPHWL
316 Stainless Steel .300" Headed Fasteners with .145"
Shank Diameter and 1" Metal Washers*
*Washers are 304 Stainless Steel, **Up to 2"
PDPWLSS
.300" Headed Fasteners with .145" Shank Diameter
and 1 7/16" Metal Washers
PINW
.300" Headed Fasteners with .145" Shank Diameter
and 1 3/8" Plastic Washers
*Up to 2 1/2 "
PINWP
.300" Headed Tophat Fasteners with .145" Shank Diameter
PDPT
Highway Basket Clips - .300" Headed Fasteners with .145" Shank Diameter
PHBC
Pre-Assembled BX Cable Straps and
Conduit Straps -
.300" Headed Fasteners with .145" Shank Diameter
PBXDP
PCC
Pre-Assembled Ceiling Clips -
.300" Headed Fasteners with .145" Shank Diameter
For alternate overhead fastening, see the Tie Wire Wedge Anchor.
PCLDP
(PCL similar
without pin)
PECLDP
3/8" Headed Fasteners* with .145" Shank Diameter
*Not intended for use in high velocity tools.
PHV3
1/4"–20 Threaded Studs*
*Shank diameter is .150"
NOTE: T = Thread Length, S = Shank Length
PSLV4
3/8"–16 Threaded Studs* (Factory Mutual Listing - see below)
* Shank diameter is .205" NOTE: T = Thread Length, S = Shank Length
** Factory Mutual Listing 3031724
PSLV3
1/4" Headed Hammer Drive Fastener with 3/8" Metal Washer
Warning: Do not use powder loads with this tool. This is a hammer drive tool only. Use of powder loads with this tool may result in injury or death.
PHD
PHT-38
Manual Hammer Tool (not for use with powered loads)
